Graphic 45 Princess Shaker Cards
Hello, Friends! Today I’m sharing some Graphic 45 Princess Shaker Cards that I created over the holiday break. I set out to make just one card…then it was two…and oops! By the time I was done playing, I had 4 Graphic 45 Princess Shaker Cards on my work desk! These will be on display in the Buttons Galore and More booth at Creativation 2019. Since these cards are designed to be displayed in a booth, I only covered the inside with basic paper panels. Therefore, I have no photos of the card interiors to share with you today.
Graphic 45 Princess Shaker Cards: Believe Wood Frame Shaker
This 5″ x 7″ card features a frame style shaker element. Here’s how I built it.
- Begin by dry brushing the largest Tim Holtz Vignette Frame with a coat of white gesso. Dry thoroughly.
- Next, brush a light layer of Tattered Rose Distress Ink over the frame.
- Now place the frame in a box with high sides and spray liberally with Tarnished Brass Distress Mica Spray. Let the spray puddle into the corners and recessed areas of the frame.
- Cut a piece of clear acrylic cardstock (4″ x 6″ as I recall) and adhere it to the back of the frame using either Scor-Tape or Art Institute Dries Clear Adhesive. Press along the edges with a clean paper towel to secure the seal. This is very important! Let it dry completely while you build your card base.
- When the frame is completely dry, add a double layer of foam tape around the perimeter, being careful not to let the tape show through the window.
- Now place a fair sized mound of Buttons Galore Blush Premium Sequins in the center of your focal image. Keep them away from the area where you will attach the frame.
- Next, carefully align your prepared frame over the image, centering it as best as you can.
- Finally, press in place to seal and adhere to the card base.
Finish the card off with a Little Birdie Crafts Oriel Vintage Blossom and a seam binding bow.
Graphic 45 Princess Shaker Cards: A Real Princess Chipboard Frame Shaker
This next shaker card uses an altered chipboard frame in lieu of a shaker box. The frame measures 3 1/2″ x 5″, but the opening is only 2 1/2″ x 2 3/4″. Here’s how I prepared this shaker box.
- First, paint a chipboard frame with white gesso and dry thoroughly.
- Next, dry brush the frame with Tattered Rose Distress Paint.
- When the paint has dried, brush a thin layer of Art Institute Dries Clear Adhesive over the entire surface.
- While the adhesive is still wet, place the frame in a funnel tray and sprinkle liberally with Rajni Chalwa’s Frosting Powder. Set it aside to dry completely.
- Cut a piece of clear acrylic cardstock to fit the size of the frame opening and adhere to the back with Art Institute Dries Clear adhesive. As before use a clean piece of paper towel to press it securely onto the back of the frame. Let this dry.
- Now adhere a double layer of foam adhesive to the back of the frame. You will need to cut strips of foam adhesive in half unless you have 1/4″ wide foam.
- Fill the cavity of the shaker box with Buttons Galore Apricot Premium Sequins.
- Fussy cut the image from the signature page of Princess. Pop up on a piece of patterned paper and adhere to the foam tape.
I finished this card off with some fussy cuts, Little Birdie Flowers, Mini Pearl Prills, Pale Gold Taffeta Ribbon, altered metal corners and an altered metal crown. To alter the metal pieces I painted them with ivory chalk paint, then spritzed with Antique Brass Mica Spray.
Graphic 45 Princess Shaker Cards: If the Crown Fits Embossed Paper Shaker Box
This card is a companion to the previous card, and uses the other princess from the signature page of the collection. After fussy cutting the princess and matting it on striped paper, I proceeded to make the frame.
- First, carefully open the seams on a Tim Holtz Cabinet Card Frame. Cut away the back portion to use in another project.
- Next, lightly sand the surface of the frame, then paint it with white gesso.
- When the gesso has dried, dry brush the frame with Tattered Rose Distress Paint and place it directly into the Tim Holtz 3D Botanical Embossing Texture Fade. Run this through your machine following the manufacturer’s directions.
- Be sure to wash the texture fade immediately to remove any traces of paint and/or gesso.
- The pressure of embossing will lift some of the gesso, but I liked this distressed look.
- Use a palette knife to add some thin layers of Opaque Crackle Texture Paste to the open areas of the frame. Let this dry.
- Next, sponge Vintage Photo Distress Ink over the raised portions of the design. Spritz very lightly with Antique Brass Mica Spray. This will sink down into the crackle paste and look very cool.
- Back the frame with clear acrylic cardstock and build your shaker box.
- Fill the cavity of the shaker box with Buttons Galore Rose Garden Shaker Mix. (You will want to remove the large and medium sized buttons from the mix first.)
Finish the card off with Little Birdie Audria Blush Flowers, gold metallic string, ribbon and a crown embellishment.
Graphic 45 Princess Shaker Cards: Easel Shaker Pocket
For the final card, I created this easel shaker pocket. This is probably the easiest way I’ve found to add a shaker element to a card. Simply stitch clear acrylic cardstock to your focal image leaving about a 2″ opening. Fill the pouch with Buttons Galore Blush Premium Sequins. Finish stitching up the pouch and you are good to go!
Adorn your card with Renae Classic Little Birdie Flowers, Light Coral Delicate Stitched Satin Ribbon and chipboard elements from the paper collection.
I hope I’ve shared some fun ideas for making shaker cards in many different ways. If so, I’d love to hear from you in the comment section below.
Thanks for stopping by!
Graphic 45 Princess Shaker Cards: Linked Supply List
Note: Sequin mixes are linked in the post
All cards use elements from the following Graphic 45 Products:
- Princess Collection
- Other Products
- Tim Holtz Vignette Frame
- White Gesso
- Tattered Rose Distress Paint
- Antique Brass Distress Mica Spray
- Little Birdie Flowers (Check your local AC Moore Craft Store)
- Tim Holtz Cabinet Cards (retired)
- Botanical 3-D Embossing Texture Fade
- Opaque Crackle Texture Paste
- Embellishments from my stash